Waterproof fiberboard on Sale-manufacture,factory,supplier from China

     The Waterproof fiberboard originated in Europe. It is based on the production of ordinary fiberboard and added with a certain proportion of granular moisture-proof particles. The fiberboard made in this way can greatly reduce the degree of expansion after encountering water.             Gaotang County Xinhua Wood Industry Co., Ltd. was established in April 2010 with a registered capital of 11 million yuan. It covers an area of about 76,600 square meters, including a construction area of about 22,000 square meters.

      Waterproof and moisture-proof board is made by adding special materials that can improve the waterproof, moisture-proof and mildew-proof performance of wood-based panels during the production of medium-density fiberboard.   It is suitable for high-humidity areas and places where accidental humidity may occur, such as kitchens Cabinets, bathroom vanity, laundry cabinet. Marked in green.

Instruction of Waterproof FiberboardWaterproof Fiberboard, also known as fiberboard , is an artificial board made of wood fiber or other plant fibers as raw materials and urea-formaldehyde resin or other suitable adhesives.Warehouse  Xinhua Wood Company Show  Gaotang County Xinhua Wood Industry Co., Ltd. was established in April 2010 with a registered capital of 11 million yuan. It covers an area of about 76,600 square meters, including a construction area of about 22,000 square meters.

Soak the common substrate and moisture-proof substrate in water at the same time, and the expansion rate of the common plate is significantly higher than that of the moisture-proof plate after two hours of expansion change. The moisture-proof board has good moisture-proof performance and is suitable for making kitchen furniture and bathroom furniture.Damp-proof board cannot be directly used on furniture, and decorative paper should be pasted on the surface. The normal practice is to soak the decorative paper in melamine solution, and then press it on after hot pressing.

Medium Density Fiberboard (MDF) is a kind of man-made board. MDF is mainly made of plant fibers or wood fibers. It is formed after the fibers are crushed, separated, dried, and urea-formaldehyde resin or other suitable adhesive is added and pressed at high temperature. Specifications of MDFXinhua Wood StoragesXinhua Wood Quality CertificationsXinhua Wood Introduction    Gaotang County Xinhua Wood Industry Co., Ltd. was established in 2010 . It covers an area of about 76,600 square meters.The company is located in Gaotang County, Liaocheng City,Shandong province, China.

     The basic unit of fiberboard is separated wood fibers or fiber bundles. The raw materials for fiber production mainly come from forest cutting residues, such as branches, shoots, small diameter wood, etc; And wood processing residues, such as board edges, shavings, sawdust, etc. In addition, the wastes from chemical processing of forest products (such as tannin extract and hydrolytic residues) and other plant stems can be used to produce fibers. The fiber content of coniferous wood is high, and the fiber length is 30-50% longer than that of hardwood.

The wood-based panel is formed by interweaving lignocellulose fibers and is made of its inherent adhesive properties. Adhesives and/or additives may be applied during manufacturing.Fiberboard, also known as density board, is a wood-based panel made of wood fiber or other vegetable fibers with urea formaldehyde resin or other applicable adhesives. Adhesives and/or additives may be applied during manufacturing. Fiberboard has the advantages of uniform material, small vertical and horizontal strength difference, and is not easy to crack. It is widely used.

The wood-primarily based panel is fashioned by interweaving lignocellulose fibers and is made of its inherent adhesive properties. adhesives and/or components can be applied for the duration of production.Fiberboard, also called density board, is a wood-primarily based panel made from wood fiber or unique vegetable fibers with urea formaldehyde resin or different relevant adhesives. adhesives and/or components can be applied at some point of manufacturing. fiberboard has the blessings of uniform cloth, small vertical and horizontal power difference, and isn't easy to crack.

Medium density fiberboard is a kind of man-made board made of wood or plant fiber through mechanical separation and chemical treatment, mixed with adhesive and waterproof agent, and then formed by high temperature and high pressure.

What is a Flame Retardant MDF Board?The flame retardant MDF board is a kind of board that can suppress the flame burning speed in the ignited state, or directly extinguish the flame.

    Fiberboard, also referred to as density board, is a timber-primarily based panel made of wood fiber or exceptional vegetable fibers with urea formaldehyde resin or other relevant adhesives. adhesives and/or additives can be carried out sooner or later of manufacturing. fiberboard has the benefits of uniform , small vertical and horizontal power distinction, and isn't easy to crack. it's miles considerably used.

    MDF is actually a kind of density board, which also includes short fiberboard and long fiberboard. MDF is mainly made of plant fibers or wood fibers. After the fibers are crushed, separated, and dried, a urea-formaldehyde resin or other suitable adhesive is added and pressed at high temperature. A kind of man-made board.The thickness of MDF is generally between 3mm-30mm, and the density of MDF is very high. Generally, the choice of MDF depends on the density of MDF to determine the quality of MDF. The density of MDF is generally It is in the range of 0.5-0.8g/cm³.

Carbon crystal panels are environmentally friendly, durable, moisture-proof, flame-retardant, sound-absorbing, anti-aging ...Advantages of Carbon Crystal MDF  Noise reductionThe carbon crystal wall panel has a good diffuse reflection for sound, and has a relatively buffering impact of the subwoofer; the sound insulation reached 29 decibels after testing, which is 13 decibels higher than the sound insulation of a 25 cm wall, which solves the incoming noise from the outside and the private space of life And office (such as conference room) interference noise.WaterproofThe carbon c

The following aspects should be paid attention to when choosing medium density fiberboard;1. From the appearance, check whether the thickness and density are uniform, whether the corners are damaged, whether there are delamination, blister, charcolization, etc., and whether there are soft parts.2. When conditions permit, you can saw a small piece of medium density fiberboard and soak it in water with a water temperature of 20°C for 24 hours to observe its thickness change, and at the same time observe whether there are small bulges on the surface of the board.

How to choose good quality MDF?1.Surface cleanliness: There should be no obvious particles on the surface of the density board with good surface cleanliness. Particles are caused by impurities brought in during the pressing process, which not only affects the appearance, but also makes the paint film easy to peel off.2.Surface smoothness: When touching the surface with hands, it should feel smooth. If it feels astringent, it means that the processing is not in place.3.Surface smoothness: The surface of the density board should be bright and smooth.

      High-density fiberboard （HDF) is a board made of wood fiber or other plant fiber, applied with urea-formaldehyde resin, or other synthetic resins under heat and pressure.    The most advanced flat pressing complete production line in the world. Therefore, the physical performance is higher and better than that of medium-density fiberboard, and its density is usually above 800kg/M3.

    Density board, also known as fiberboard, is a man-made board made of wood fiber or other plant fiber and applied with urea-formaldehyde resin or other suitable adhesives. According to its density, it can be divided into high density board, medium density board and low density board.

    MDF is actually a kind of density board, which also includes short fiberboard and long fiberboard. MDF is mainly made of plant fibers or wood fibers. After the fibers are crushed, separated, and dried, a urea-formaldehyde resin or other suitable adhesive is added and pressed at high temperature. This kind of man-made board is often used in interior decoration.Xinhua Wood Storage  Quality Certificates  Gaotang County Xinhua Wood Industry Co., Ltd. was established in April 2010 with a registered capital of 11 million yuan.

          High-density fiberboard (English name: High Density Fiberboard, abbreviated as HDF) is a board made of wood fiber or other plant fiber, applied with urea-formaldehyde resin, or other synthetic resins under heat and pressure.          The most advanced flat pressing complete production line in the world. Therefore, the physical performance is higher and better than that of medium-density fiberboard, and its density is usually above 800kg/M3.

High Density Fiberboard Introduction:Density board, also known as fiberboard (full name: MDF fiberboard), is a man-made board made of wood fibers or other plant fibers with the application of urea-formaldehyde resin or other applicable adhesives.

What is Black MDF ? What advantages does Black MDF have?    Carbon is a non-metallic element that is stable at room temperature, unreactive, and has extremely low toxicity to the human body. It can be safely ingested in the form of graphite or activated carbon. Carbon crystal, the full name of carbon microcrystal, is a crystal structure of carbon.

What is carbon crystal wooden door？ Carbon crystal is a kind of microcrystalline carbon particles purified from minerals, commonly known as high carbon graphite. This material is harder than steel and lighter than aluminum, it is high temperature resistant, corrosion resistant, and has a stable molecular structure. Carbon crystal fiber board, waterproof, zero formaldehyde, ultra-high density, is a high-end product worth having. And the carbon crystal wooden door, the wooden door made of this carbon element crystal.Advantages of carbon crystal wood doors1.

What is Fire Resistant MDF ?How to produce it ? What is its application?The fireproof board is a kind of board that can suppress the burning speed of the flame in the ignited state, or directly extinguish the flame.

Carbon Crystal Panel and Its AdvantagesCarbon crystal panel is generally used in paint-free technology, with high environmental protection and good moisture resistance. In terms of materials, they all belong to composite boards. If they are under the same brand, the quality of carbon crystal boards is better. In contrast, carbon crystal panels are waterproof, moisture-proof, environmentally friendly, formaldehyde-free, crack-resistant and non-deformable. Carbon crystal plate is a new type of high-tech environmental protection material.