Moisture proof MDF-manufacture,factory,supplier from China

    Medium density fiberboard is made of wood fiber and other fibers as raw materials, prepared by fiber, then applied with synthetic glue and other functional materials, and pressed into boards with different thicknesses and densities under heat and pressure. Among them, the moisture-proof MDF is made of modified melamine cyanamide adhesive or MDI type adhesive, and the use of waterproofing agent is improved at the same time.

Moistureproof board is to add a certain proportion of moistureproof particles in the production process of the base material, also known as melamine board (base material), which can greatly reduce the degree of expansion of the board when encountering water.  Gaotang County Xinhua Wood Industry Co., Ltd. was established in April 2010 with a registered capital of 11 million yuan. It covers an area of about 76,600 square meters, including a construction area of about 22,000 square meters.

Soak the common substrate and moisture-proof substrate in water at the same time, and the expansion rate of the common plate is significantly higher than that of the moisture-proof plate after two hours of expansion change. The moisture-proof board has good moisture-proof performance and is suitable for making kitchen furniture and bathroom furniture.Damp-proof board cannot be directly used on furniture, and decorative paper should be pasted on the surface. The normal practice is to soak the decorative paper in melamine solution, and then press it on after hot pressing.

      Waterproof and moisture-proof board is made by adding special materials that can improve the waterproof, moisture-proof and mildew-proof performance of wood-based panels during the production of medium-density fiberboard.   It is suitable for high-humidity areas and places where accidental humidity may occur, such as kitchens Cabinets, bathroom vanity, laundry cabinet. Marked in green.

Particleboard Quality Judgment1. From the appearance point of view, look at the size and shape of the wood chips in the center of the cross-section. The length is generally 5-10MM in length. If the length is too long, the structure is loose, and if it is too short, the deformation resistance is poor, and the so-called static bending strength does not meet the standard;2. The moisture resistance of wood-based panels depends on its density and moisture-proof agent.

FR MDF Advantages:1.The fireproof board has low hygroscopicity, stable water-absorbing thickness expansion rate, and excellent moisture-proof performance. It is especially suitable for secondary processing such as finishes, adhesives, and paints.

According to density, it can be divided into: high-density fiberboard, medium-density fiberboard, and low-density fiberboard (the density of medium-density fiberboard is 500 kg/m3-880 kg/m3, and the density of high-density fiberboard is ≥800 kg/m3).According to the national standard (GB/T 11718-2021), it is divided into: ordinary MDF, furniture MDF and load-bearing MDF.According to the use, it can be divided into: furniture board, floor base material, door panel base material, electronic circuit board, engraving and milling board, moisture-proof board, fire-proof board and line board

Carbon Crystal Panel and Its AdvantagesCarbon crystal panel is generally used in paint-free technology, with high environmental protection and good moisture resistance. In terms of materials, they all belong to composite boards. If they are under the same brand, the quality of carbon crystal boards is better. In contrast, carbon crystal panels are waterproof, moisture-proof, environmentally friendly, formaldehyde-free, crack-resistant and non-deformable. Carbon crystal plate is a new type of high-tech environmental protection material.

Carbon crystal panels are environmentally friendly, durable, moisture-proof, flame-retardant, sound-absorbing, anti-aging ...Advantages of Carbon Crystal MDF  Noise reductionThe carbon crystal wall panel has a good diffuse reflection for sound, and has a relatively buffering impact of the subwoofer; the sound insulation reached 29 decibels after testing, which is 13 decibels higher than the sound insulation of a 25 cm wall, which solves the incoming noise from the outside and the private space of life And office (such as conference room) interference noise.WaterproofThe carbon c

FeaturesThe density board surface is smooth and flat, the material is fine and dense, the performance is stable, the edge is firm, and the surface of the board is very decorative. But the density board has poor moisture resistance. In contrast, the nail-holding force of MDF is worse than that of particleboard.

Advantages of Carbon Crystal Plates or Black MDFCarbon crystal panels are environmentally friendly, durable, moisture-proof, flame-retardant, sound-absorbing, anti-aging and other practical and excellent features, helping you easily have a healthy, environmentally friendly and safe living home.Noise reductionThe carbon crystal wall panel has a good diffuse reflection for sound, and has a relatively buffering impact of the subwoofer; the sound insulation has reached 29 decibels after testing, which is 13 decibels higher than the sound insulation of a 25 cm wall, which solves the incoming noise

How to deal with the pungent smell of the density board?1） Keep the room ventilated and paint the MDF with anti-mildew paint.Put the density board in a dry place at home, keep the room ventilated, and it can be exposed to the sun if it is severely damp. Go to the market to buy anti-mildew paint and paint the MDF. It can play a certain role in preventing moisture and mildew, but pay attention to the quality of the paint and choose non-toxic and tasteless products.

1. Physical and mechanical propertiesBecause the fiber structure of the board is uniform and the bonding strength between fibers is high, its static bending strength, plane tensile strength and elastic modulus are good. However, because MDF is made of logs that are ground into fibers, which completely changes the structure of the wood, it has higher moisture absorption, water absorption performance, and higher thickness expansion rate, and its nail holding power is worse than that of particleboard.2.

     The Waterproof fiberboard originated in Europe. It is based on the production of ordinary fiberboard and added with a certain proportion of granular moisture-proof particles. The fiberboard made in this way can greatly reduce the degree of expansion after encountering water.             Gaotang County Xinhua Wood Industry Co., Ltd. was established in April 2010 with a registered capital of 11 million yuan. It covers an area of about 76,600 square meters, including a construction area of about 22,000 square meters.

Advantages of MDF1. The density of medium density fiberboard is very high, so it is called MDF. Its surface can be pasted with melamine or wood veneer. Its physical properties are very good, the material is uniform, and there is no dehydration problem, so it will not be deformed by moisture.2. Medium density fiberboard is made of crushed plant fibers and pressed at high temperature, so the surface of this board is very smooth and square. It can be used not only as furniture materials, but also as decorative panels, light metal sheets, veneer, etc.3. Is MDF high in formaldehyde?1.

FeaturesThe density board surface is smooth and flat, the material is fine and dense, the performance is stable, the edge is firm, and the surface of the board is very decorative. But the density board has poor moisture resistance. In contrast, the nail-holding force of MDF is worse than that of particleboard. If the screws loosen after tightening, it is difficult to fix them at the same position.The main advantage1. Density board is easy to be painted. All kinds of paints and paints can be evenly coated on the density board, which is the first choice for paint effect.2.

FeaturesThe density board surface is smooth and flat, the material is fine and dense, the performance is stable, the edge is firm, and the surface of the board is very decorative. But the density board has poor moisture resistance. In contrast, the nail-holding force of MDF is worse than that of particleboard. If the screws loosen after tightening, it is difficult to fix them at the same position.The main advantage1. Density board is easy to be painted. All kinds of paints and paints can be evenly coated on the density board, which is the first choice for paint effect.2.

  1. The characteristics of density board: the surface of density board is smooth and flat, the material is fine and dense, the performance is stable, the edge is firm, and the surface of the board is decorative. However, density boards have poor moisture resistance, and in comparison, density boards have poorer nail-holding power than particle boards. If the screws loosen after tightening, it is difficult to fix them again due to the low strength of density boards.2. The use of MDF: mainly used for laminate flooring, door panels, partition walls, furniture, etc.

Manufacturing Process Broadcast1. Chipping: It is the manufacturing workshop of the raw materials in the whole board production. It mainly cuts loose wood into wood chips that meet the production specifications, so as to provide better conditions for fiber separation in preparation for heat.2. Thermal grinding. The wood chips cut out of the chipping workshop are preheated and cooked, and then mechanically separated to obtain fibers.3. Fiber drying: heat grinding and sizing to make the moisture content of the fiber reach 40%-50%.

Advantages of OSB BoardOSB (Oriented Strand Board) is a composite board made of wood veneer or strands, which has many advantages, these advantages include:1.Strength and Durability: OSB board is constructed of interlaced veneer veneers, making it stronger than traditional particle board. It is able to withstand greater loads and pressures and has better resistance to tearing, making it more durable.  2.Stability: Due to the way OSB panels are constructed, they are not susceptible to moisture and deformation.

What is a Flame Retardant MDF Board?The flame retardant MDF board is a kind of board that can suppress the flame burning speed in the ignited state, or directly extinguish the flame.

The Difference Between Plywood and MDFWood fibers, resins or glues are used to make MDF. These bond together under pressure and heat to form a cardboard. Plywood is made by gluing thin hardwoods between pieces of wood.Plywood is made of solid wood while MDF is made of wood fibers. In manufacturing, there is some waste in plywood production, whereas there is no waste in MDF production.When comparing the two, it can be seen that plywood has attractive grains or knots. However, these particles or nodules are not visible in MDF.Furniture can easily be made from MDF instead of plywood.

The difference between flame-retardant MDF and ordinary MDF Appearance difference: Flame-retardant MDF is a kind of functional MDF. From the appearance, it is red, mainly because the fiber is dyed with red dye according to the international customary calendar, so as to distinguish it from ordinary MDF. Physical and mechanical properties Flame-retardant MDF is also MDF. First of all, it must have the physical mechanics of ordinary MDF to meet the use requirements.

1. Introduction of MDFMDF is actually a kind of density board, which also includes short fiberboard and long fiberboard. MDF is mainly made of plant fibers or wood fibers. After the fibers are crushed, separated, and dried, a urea-formaldehyde resin or other suitable adhesive is added and pressed at high temperature. A kind of man-made board.2. MDF sizeThe thickness of MDF is generally between 3mm-30mm, and the density of MDF is very high. Generally, the choice of MDF depends on the density of MDF to determine the quality of MDF.