Medium Density Fiberboard on Sale-manufacture,factory,supplier from China

Medium Density Fiberboard (MDF) is a kind of man-made board. MDF is mainly made of plant fibers or wood fibers. It is formed after the fibers are crushed, separated, dried, and urea-formaldehyde resin or other suitable adhesive is added and pressed at high temperature. Specifications of MDFXinhua Wood StoragesXinhua Wood Quality CertificationsXinhua Wood Introduction    Gaotang County Xinhua Wood Industry Co., Ltd. was established in 2010 . It covers an area of about 76,600 square meters.The company is located in Gaotang County, Liaocheng City,Shandong province, China.

Medium Density Fiberboard Introduction:Density board, also known as fiberboard (full name: MDF fiberboard), is a man-made board made of wood fiber or other plant fiber, applied with urea-formaldehyde resin or other suitable adhesives. According to its density, it can be divided into high density board, medium density board and low density board. Mainly used for laminate flooring, door panels, partition walls, furniture, etc.

     The Waterproof fiberboard originated in Europe. It is based on the production of ordinary fiberboard and added with a certain proportion of granular moisture-proof particles. The fiberboard made in this way can greatly reduce the degree of expansion after encountering water.             Gaotang County Xinhua Wood Industry Co., Ltd. was established in April 2010 with a registered capital of 11 million yuan. It covers an area of about 76,600 square meters, including a construction area of about 22,000 square meters.

The following aspects should be paid attention to when choosing medium density fiberboard;1. From the appearance, check whether the thickness and density are uniform, whether the corners are damaged, whether there are delamination, blister, charcolization, etc., and whether there are soft parts.2. When conditions permit, you can saw a small piece of medium density fiberboard and soak it in water with a water temperature of 20°C for 24 hours to observe its thickness change, and at the same time observe whether there are small bulges on the surface of the board.

High Density Fiberboard Introduction:Density board, also known as fiberboard (full name: MDF fiberboard), is a man-made board made of wood fibers or other plant fibers with the application of urea-formaldehyde resin or other applicable adhesives.

Medium Density Fiberboard classification:       According to the density, it can be divided into high-density board, medium-density board, and low-density board (the density of medium-density board is 550 kg-880 kg/m3, and the density of high-density board is more than 880 kg/m3). Commonly used specifications are 1220*2440mm and 1525*2440mm, and the thickness is 2.0mm~25mm.

    Density board, also known as fiberboard, is a man-made board made of wood fiber or other plant fiber and applied with urea-formaldehyde resin or other suitable adhesives. According to its density, it can be divided into high density board, medium density board and low density board.

          High-density fiberboard (English name: High Density Fiberboard, abbreviated as HDF) is a board made of wood fiber or other plant fiber, applied with urea-formaldehyde resin, or other synthetic resins under heat and pressure.          The most advanced flat pressing complete production line in the world. Therefore, the physical performance is higher and better than that of medium-density fiberboard, and its density is usually above 800kg/M3.

   Density board, also known as fiberboard, is an artificial board made of wood fiber or other plant fiber by hot pressing after slicing, cooking, fiber separation, and drying, then applying urea-formaldehyde resin or other suitable adhesives. the   According to the density, it can be divided into low-density board (weight less than 550KG/M3), also known as low-density fiberboard. Medium density board (weight 550~880KG/M3), also known as medium density fiberboard.

    MDF is actually a kind of density board, which also includes short fiberboard and long fiberboard. MDF is mainly made of plant fibers or wood fibers. After the fibers are crushed, separated, and dried, a urea-formaldehyde resin or other suitable adhesive is added and pressed at high temperature. A kind of man-made board.The thickness of MDF is generally between 3mm-30mm, and the density of MDF is very high. Generally, the choice of MDF depends on the density of MDF to determine the quality of MDF. The density of MDF is generally It is in the range of 0.5-0.8g/cm³.

What is a Flame Retardant MDF Board?The flame retardant MDF board is a kind of board that can suppress the flame burning speed in the ignited state, or directly extinguish the flame.

      High-density fiberboard （HDF) is a board made of wood fiber or other plant fiber, applied with urea-formaldehyde resin, or other synthetic resins under heat and pressure.    The most advanced flat pressing complete production line in the world. Therefore, the physical performance is higher and better than that of medium-density fiberboard, and its density is usually above 800kg/M3.

National Standard for Medium Density FiberboardMedium density fiberboard is a kind of man-made board with a density of about 0.5-0.88gcm3 after processing selected wood raw materials into fibers, adding urea-formaldehyde resin and other additives, and making it through a special process.

Variety of Wood Panel1. Low density fiberboard It is a panel made of wood or plant fiber shavings that are applied with a large amount of urea-formaldehyde glue and auxiliary materials. Its density is lower than 450 kg/m3, the fiber particles are larger, the internal structure is not uniform, the strength is relatively insufficient, and the weight is light.2. Medium density fiberboardIt is a board made of wood fiber or other plant fiber, added with urea-formaldehyde adhesive, and pressed under high temperature and high pressure.

      Waterproof and moisture-proof board is made by adding special materials that can improve the waterproof, moisture-proof and mildew-proof performance of wood-based panels during the production of medium-density fiberboard.   It is suitable for high-humidity areas and places where accidental humidity may occur, such as kitchens Cabinets, bathroom vanity, laundry cabinet. Marked in green.

Soak the common substrate and moisture-proof substrate in water at the same time, and the expansion rate of the common plate is significantly higher than that of the moisture-proof plate after two hours of expansion change. The moisture-proof board has good moisture-proof performance and is suitable for making kitchen furniture and bathroom furniture.Damp-proof board cannot be directly used on furniture, and decorative paper should be pasted on the surface. The normal practice is to soak the decorative paper in melamine solution, and then press it on after hot pressing.

What is medium density fiberboard (MDF)?      Medium density fiberboard (MDF) is a kind of man-made board made of hardwood, softwood fiber or other plant fiber, which is crushed, separated, dried, applied with urea-formaldehyde resin or other suitable adhesives, and then hot-pressed. Medium-density fiberboard (MDF), generally denser than plywood, is made of separated fibers, but like plywood can be used as a building material.

Carbon crystal panels are environmentally friendly, durable, moisture-proof, flame-retardant, sound-absorbing, anti-aging ...Advantages of Carbon Crystal MDF  Noise reductionThe carbon crystal wall panel has a good diffuse reflection for sound, and has a relatively buffering impact of the subwoofer; the sound insulation reached 29 decibels after testing, which is 13 decibels higher than the sound insulation of a 25 cm wall, which solves the incoming noise from the outside and the private space of life And office (such as conference room) interference noise.WaterproofThe carbon c

How to choose good quality MDF?1.Surface cleanliness: There should be no obvious particles on the surface of the density board with good surface cleanliness. Particles are caused by impurities brought in during the pressing process, which not only affects the appearance, but also makes the paint film easy to peel off.2.Surface smoothness: When touching the surface with hands, it should feel smooth. If it feels astringent, it means that the processing is not in place.3.Surface smoothness: The surface of the density board should be bright and smooth.

     Density board is called medium density fiberboard（MDF) . It is made of wood fiber or other plant fiber, prepared by fiber, applied with synthetic resin, and pressed under heat and pressure. According to its density, it can be divided into high-density fiberboard, medium-density fiberboard and low-density fiberboard. It is widely used in the fields of furniture manufacturing and decoration in China.Xinhua Wood Show  Xinhua Wood Machinery  Gaotang County Xinhua Wood Industry Co., Ltd.

    Advantages of Carbon Crystal Medium Density Fibreboard:1. High environmental protection performance.The product does not need to be painted after coating, reducing the harm of formaldehyde to human body, and the environmental protection grade is higher than the national environmental protection standard. 2.

1. Physical and mechanical propertiesDue to the uniform fiber structure of the board and the high bonding strength between fibers, its static bending strength, plane tensile strength, elastic modulus, and screw-holding force are better than particleboard. Hygroscopicity, water absorption performance, thickness expansion rate is low.2. Decorative performanceBecause the surface of medium density fiberboard is flat and smooth, it is easy to glue planed veneer and tissue paper and other decorative materials, and it is easy to paint and save paint.3.

Medium density fiberboard is a kind of man-made board made of wood or plant fiber through mechanical separation and chemical treatment, mixed with adhesive and waterproof agent, and then formed by high temperature and high pressure.

     The density of medium density board is between the density of high density board and low density board, generally 650~880kg/m. The common specification is 2440mm*1220mm, and the thickness is 1mm, 3mm, 5mm, 9mm, 12mm, 15mm, 18mm, 25mm, etc. . MDF with other special specifications and thicknesses can also be customized.How to identify high-quality MDF?1.Surface cleanliness: There should be no obvious particles on the surface of the density board with good surface cleanliness.